Originally posted by smart-prog
View Post
-
Sorted it was wrong pinout -
CAN wires wrong location to my moduleComment
-
My pinout needed to be the lower bottom 2 pinsYou do not have permission to view this gallery.
This gallery has 1 photos.Comment
-
-
please can you help me with actuvation of tc22xx infineon? i paid yesterday but not recieved my certificate.
thankyouComment
-
Marca de coches NOMBRE : TOYOTA
MODELO : FORTUNER
NÚMERO DE PARTE : 89170-0KB70
CPU / memoria EEPROM :R5F6172X
they help me to read it with smart OBD because in the images I don't get the corresponding oneYou do not have permission to view this gallery.
This gallery has 4 photos.Comment
-
I apologize if I have the wrong section ... but I can't open a new discussion ....
I just bought my airbag start pack, I have a problem with the USB dongle with the sw bag can service tool ....
the dongle continues to disconnect and reconnect by itself.
all the boxes in the lower left from green to red in continuation .....
I have already updated the drivers, I am attaching a screen of the devices on my win10 64bit
whit ast no problem...dongle is connect regular
screen dongle hw.png
Comment
-
-
Thank you for reply.....
no usb hub, dongle direct to usb pc.
i have also seen videos on the internet and I see the same my fault on some ......
changed usb port but same defect...Comment
-
Hello, can I use Smart OBD for diagnosing the SRS GN15-14B321-GF unit for the Ford Ecosport car.
Will the connection for this block coincide with those blocks that are specified in the program, or is it better to double-check?Last edited by Elder; 14.11.2019, 16:24.Comment
-
-
In my SRS block, pin No. 11 calls with "0" resistance to the block's ground and not as indicated in the picture for Smart OBD.
Connected, read errors.Comment
-
You do not have permission to view this gallery.
This gallery has 2 photos.Comment
-
-
GN15-14B321-GFComment
-
-
What is the error?
You may just need to replace the seat weight sensor.Today, 11:32 -
Reply to 95910-cw500 not workIt has been done and I will try it on the car and let you know....Today, 11:14
-
Reply to 89170-53790Read and post the dataflash file, it may need to be fixed.
Password in PM....Today, 11:07 -
Reply to CANFD adapter activationPCB photosYou do not have permission to view this gallery.
This gallery has 2 photos.Today, 11:05 -
Hi
I have three PV4T-14B321-AB to reset.
First one reset perfectly OK on workbench by diag.
Other two are stopping...Today, 11:04 -
Reply to 95910-cw500 not workFirst connect and clean the MCU, after writing the cleared file to the MCU, unsolder the EEPROM and clear it.Today, 11:03
-
-
The files look fine, try connecting again.
In the future, please run diagnostics before performing any operations.Today, 11:00 -
Sorry For Repost But For Some Reason Old Post Was UNAPPROVED and would not let me edit it.
Hi
I have an Audi Siemens Airbag...Today, 10:57 -
Reply to Fiat tipo 00052195566It is not recommended to write pflash on this MCU.
Here is why it is forbidden on cpt.Today, 10:52 -
The accident data has changed status to history.
It will be cleared on the car.Today, 10:48 -
AirbagCANServiceTool supports Clear Crash by dump for this part number.Today, 10:46
-
Reply to CANFD adapter activationThere may be some problem with SmartOBD.
Take a photo of the SmartOBD PCB.Today, 10:44 -
Reply to 95910-cw500 not workIt means removing the EEPROM and doing it.
Should I remove the EEPROM after dflash or remove the EEPROM before dflash? Please provide me with the...Today, 10:31
Comment