Kia Ceed 2020 95910-cr300 renasas R7F7010423 eeprom 95512 Not clearing crash

[mclaughlin8882]

Hello, im having this problem when tring to clear data,when i click on clear faults,it says its cleared but when i read for faults again,they all show up again,
does smart obd support this module?

KIA XCeed Continental 95910-CR300 (on bench)
Enable 12V on Extended Connector... ok
External power +11.27V
Enter Diagnostic Session... ok
Read Part Number... 95910-CR300
Read ACU Coding... CD31
Read Errors...
B1346:00-89 - DRIVER AIR BAG(DAB) RESISTANCE-HIGH
B1352:00-89 - PASSENGER AIR BAG(PAB) RESISTANCE-HIGH
B1378:00-89 - SIDE AIRBAG FRONT-DRIVER RESISTANCE TOO HIGH
B1382:00-89 - SIDE AIRBAG FRONT-PASSENGER RESISTANCE TOO HIGH
B1473:00-89 - INFLATABLE CURTAIN AIRBAG DRIVER RESISTANCE TOO HIGH
B1477:00-89 - PASSENGER CURTAIN RESISTANCE.-HIGH
B1361:00-89 - PRETENSIONER FRONT-DRIVER RESISTANCE TOO HIGH
B1367:00-89 - PRETENSIONER FRONT-PASSENGER RESISTANCE TOO HIGH
B136A:00-89 - PRETENSIONER REAR-DRIVER RESISTANCE TOO HIGH
B136E:00-89 - PRETENSIONER REAR-PASSENGER RESISTANCE TOO HIGH
B1527:00-89 - PASSENGER AIRBAG ON/OFF SWITCH OPEN OR SHORT TO BATTERY
B2505:00-89 - PASSENGER AIRBAG ON/OFF WARNING LAMP FAILURE
B2617:00-89 - Unknown Error
B1334:00-89 - FIS(FRONT IMPACT SENSOR)-PASSENGER COMMUNICATION ERROR
B1329:00-89 - FIS(FRONT IMPACT SENSOR)-DRIVER COMMUNICATION ERROR
B1117:00-89 - Unknown Error

[greencamp]

Hi, you must press CLEAR CRASH, but not clear errors

[greencamp]

Your log hanv't crash error. Instal on car and cler errors.

[mclaughlin8882]

Hello and thanks for helping,i have selected clear crash by obd first and this is what i get,but i did select clear errors after that is that what im doing wrong?

heres the log after selecting clear crash by obd

Enable 12V on Extended Connector... ok
External power +11.23V
Set ServiceMode...
Open Diagnostic Session... ok
Get Seed... ok
Enter Password... ok
Get Seed2... ok
Enter Password2... ok
Reboot...
!!! WARNING !!! Turn Off Ignition On Car !!! WARNING !!!
!!! WARNING !!! Turn On Ignition On Car !!! WARNING !!!
Enable 12V on Extended Connector... ok
External power +11.24V
Connect... ok
Synchronization... ok
Get Seed... ok
Enter Password... ok
Start Communication... ok
Clear Crash In EEPROM... ok
Clear Crash In CPU... ok

[greencamp]

Its log is good. Install on car and clear errors

[mclaughlin8882]

Ok i will try that and report back,thank you for your help

[mclaughlin8882]

Its log is good. Install on car and clear errors

Hey just checking,when you say clear errors after installed,did you mean just use a scan tool to clear them or the actual smart obd??

[greencamp]

Yes, diag tool or smartOBD

[mclaughlin8882]

Ok i have snapon diag tool,i will try with that
thank you

[smart-prog]

in You list error i not see crash record what problem you have?

[mclaughlin8882]

Hello, I’m my first post, I was getting all those errors from
module that was in a crash,when I click clear crash by obd it clears but when I read errors after they all show up again, I have just bought the tool so still learning with it.thanks

[mclaughlin8882]

[Hello, I’m my first post, I was getting all those errors from
module that was in a crash,when I click clear crash by obd it clears but when I read errors after they all show up again, I have just bought the tool so still learning with it.thanks

QUOTE=smart-prog;n89204]in You list error i not see crash record what problem you have? [/QUOTE]

[smart-prog]

Install ECU in car and CLEAR error code!

[mclaughlin8882]

Install ECU in car and CLEAR error code!

Thabk you,will do this

[mclaughlin8882]

Install ECU in car and CLEAR error code!

Just to let you know,airbag has been now installed and working perfectly,thank you for your help