I had the same problem
Announcement
Collapse
No announcement yet.
- ERR: 201
Collapse
X
-
Originally posted by audi View Post
Found interface s/n : 89F380BE3FD4EB74
Status : normal mode
- ERR: 201 for S/n: 89F380BE3FD4EB74
- ERR: 201 for S/n: 89F380BE3FD4EB74
The first was replaced with new equipment, there will be no second time.
Comment
-
Originally posted by LockBit View Post
Your CPT developer has been misused and has been permanently banned!
The first was replaced with new equipment, there will be no second time.Hello friends, if you need help, please PM.
Comment
-
-
-
Originally posted by LockBit View Post
I read your messages, your CPT has been unlocked. But if it happens again, I won't be so nice!
Run the CPT program to update the programmer. Make sure your internet connection is stable and secure. Good luck!Hello friends, if you need help, please PM.
Comment
-
Originally posted by PicoVim View PostI am currently facing this same issue:
Found interface s/n : 171BFCAFCB7FF7D8
Status : normal mode
- ERR: 201 for S/n: 171BFCAFCB7FF7D8
- ERR: 201 for S/n: 171BFCAFCB7FF7D8
Done yesterday.
We have talk already direct by WhatsApp.
Regards
Gregdiagcar.eu WhatsApp +48 509 399 633
Comment
We are open for you
Collapse
Mon - Fri
10 AM - 6 PM
Current time is:
Latest Activity
Collapse
-
by quesada auto2023 NISSAN SENTRA
98820-6LB0B
EPROM 95128
please help clear dump Thank
HELLO
I AM HAVING PROBLEMS WITH AST, SELL...-
Channel: EEPROM Programmer
Today, 04:00 -
-
by kassemBKHONDA CRV 2012
77960-T0A-N0130M1
EEPROM CHIP NUMBER 564WQ K142
READ IT BY AUTEL ST95640
I need clean crash data
thank...-
Channel: AirBag CAN Service Tool
Today, 02:04 -
-
by SimanHi
Could you please see below dump file and see if its correct? I have read this dump and cleared errors using AST, But since that it gives me B0100...-
Channel: EEPROM Programmer
Today, 00:15 -
-
Reply to 2018 ram 3500, 68346751aa 95256by AlfredGarageHI the file it's not working, it's the same issue, I tried both files that you sent me, I waiting for a good response thank you....
-
Channel: AirBag CAN Service Tool
Yesterday, 17:53 -
-
Reply to Suzuki spacia module lostby AST_SupportMistakes happen, and no one is secured from them.
In most cases, it is enough to check the GND pin to the metal case with a multimeter.-
Channel: AirBag CAN Service Tool
18.05.2024, 18:03 -
-
Reply to Suzuki spacia module lostby majidali007This is 100% okay im done this pinouts many modules working good...
-
Channel: AirBag CAN Service Tool
18.05.2024, 17:58 -
-
Reply to Suzuki spacia module lostby TroperNow i am afraid after this module lost.due to wrong type of connection in Software Added.
-
Channel: AirBag CAN Service Tool
18.05.2024, 17:52 -
-
Reply to Suzuki spacia module lostby AST_SupportYes, there are some bugs in the program that we always fix.
But your connector is different from the one in the picture. You should have asked about...-
Channel: AirBag CAN Service Tool
18.05.2024, 16:11 -
-
by TroperThis problem i have also facing .check three other same part num .but no luck
-
Channel: AirBag CAN Service Tool
18.05.2024, 15:57 -
-
by belazas4I open sensor and found processor R5F2154You do not have permission to view this gallery.
This gallery has 1 photos.-
Channel: AirBag CAN Service Tool
18.05.2024, 14:18 -
-
by TroperCOMPANY suzuki
car spacia
year 2019
part num 38910-79R0
mcu R7F701A383
hello admin the above part num which shows in software...-
Channel: AirBag CAN Service Tool
18.05.2024, 13:19 -
-
Reply to 1005273-00-fby AST_SupportLight still on because of this error.
B1315:04-81 - !!! CRASH DATA STORED !!! (System Internal Failure)
Try automatic mode without a resi...-
Channel: AirBag CAN Service Tool
18.05.2024, 12:12 -
-
Reply to 1005273-00-fby kassemBKTesla Model S Delphi 1005273-00-F (on bench with RES1K)
1. Connect and Read DTC
2. Disassamble Airbag ECU and solder resistor 1kOm as shown...-
Channel: AirBag CAN Service Tool
18.05.2024, 11:10 -
-
Reply to 2018 ram 3500, 68346751aa 95256by AlfredGaragePLs send me the password thank you.
-
Channel: AirBag CAN Service Tool
18.05.2024, 03:26 -
-
Reply to Ford Ka 51925901 Internal errorby IncarpaulHi it’s not a data issue. The original dump is working ok on another ecu. It’s down to some component on the pcb, just seeing if anyone...
-
Channel: AirBag Service Tool by DUMP
17.05.2024, 19:26 -
Comment