Peugeot 208, 9812713380 (0285012924)

[Siman]

Hi
I have cleared this srs unit using AST Cleared file. everything went ok. but, when I check DTC at the end, so not sure if reset was done correctly. could you please see below details and advice. Many Thanks.
Peugeot 208 Bosch 9812713380 (0285012924)
--------------------------------------------------------
Enable 12V on Extended Connector... ok
External power +11.6V
Set ServiceMode... ok
Read Errors...
B140E:00-09 - !!! FRONT AIRBAGS FIRED !!!
B140A:00-09 - !!! PRETENSIONERS FIRED !!!
B0001:1B-09 - DRIVER FRONTAL STAGE 1 DEPLOYMENT CONTROL (Circuit Resistance Above Threshold)
B0010:1B-09 - PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL (Circuit Resistance Above Threshold)
B0072:1B-09 - PASSENGER SEATBELT PRETENSIONER „A“ DEPLOYMENT CONTROL (Circuit Resistance Above Threshold)
B0070:1B-09 - DRIVER SEATBELT PRETENSIONER DEPLOYMENT CONTROL (Circuit Resistance Above Threshold)
B0010:11-08 - PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL (Circuit Short To Ground)
B1400:64-09 - Unknown Error (Signal Plausibility Failure)
B1401:05-09 - Unknown Error (System Programming Failure)
U1F03:87-09 - Unknown Error (Missing messages)
U1F00:00-09 - Unknown Error
Read Part Number... 9812713380
Read VIN... VF3CCHMZ6HW129344

--------------------------------------------------------
Enable 12V on Extended Connector... ok
External power +11.65V
Connect...
Enable 12V on Extended Connector... ok
External power +11.65Vok
Enter Password... ok
Creating backup "Peugeot 9812713380 95320 23.02.2024 12.06.27.bin" ok
Reading EEPROM... ok

Warning!!!
TURN OFF IGNITION OR 12V POWER SUPPLY FROM AIRBAG, WAIT 30 SECONDS AND TURN ON

Opened file: C:\Users\Nuwan\Documents\yawar16\9812713380 crashed bin_cleared_by_AST.bin
--------------------------------------------------------
Clearing Crash Data in dump file...
CRASH and ERRORS Cleared.

--------------------------------------------------------
Enable 12V on Extended Connector... ok
External power +11.62V
Connect...
Enable 12V on Extended Connector... ok
External power +11.64Vok
Enter Password... ok
Writing EEPROM... ok

Warning!!!
TURN OFF IGNITION OR 12V POWER SUPPLY FROM AIRBAG, WAIT 30 SECONDS AND TURN ON

--------------------------------------------------------
Enable 12V on Extended Connector... ok
External power +11.63V
Set ServiceMode... ok
Read Errors...
U1F03:87-09 - Unknown Error (Missing messages)
B1400:64-09 - Unknown Error (Signal Plausibility Failure)
Clear Errors... ok
Read Part Number... 9812713380

--------------------------------------------------------
Enable 12V on Extended Connector... ok
External power +11.63V
Set ServiceMode... ok
Read Errors...
U1F03:87-09 - Unknown Error (Missing messages)
B1400:64-09 - Unknown Error (Signal Plausibility Failure)
Read Part Number... 9812713380
Read VIN... VF3CCHMZ6HW129344

--------------------------------------------------------
Enable 12V on Extended Connector... ok
External power +11.64V
Set ServiceMode... ok
Read Errors...
U1F03:87-09 - Unknown Error (Missing messages)
B1400:64-09 - Unknown Error (Signal Plausibility Failure)
B1401:05-09 - Unknown Error (System Programming Failure)
U1F00:00-09 - Unknown Error
Read Part Number... 9812713380
Read VIN... VF3CCHMZ6HW129344

[AST_Support]

It's normal for the Peugeot SRS ECU, it won't boot normally and recover all errors, but on the car all will be fine.

[Siman]

Thankyou very much for the advice, much appreciated.