95910-T6100 Hyundai Genesis GV80

[qsrkoly]

Hello, help me clean up the file. 95910-T6100 Hyundai Genesis GV80 2020 tticore TC233LP16F

[smart-prog]

Please test this file!
Password in PM.
Post result here!
P.S.no result no help

[smart-prog]

And if You have Smart-OBD please Check 95910-S2000 for Read and Write data via OBD (possible in car and table)..
Post Result!

[qsrkoly]

Thank you, the result is later the car is disassembled. I tried 95910-S2000 through diagnostics earlier on the car - there was no reading only of the error. on the table could not connect.

[smart-prog]

Thanks! I wait info about dump!

[qsrkoly]

today the car has arrived for assembly. The srs block is installed. diagnostics 05/20/2021

Read ECU Delivery Assembly Number...
95910-T6100
Read Errors... ok
B1650:00-89 - !!! SRSCM CRASH RECORDED !!!
B1649:00-89 - !!! CRASH RECORDED - ROLLOVER EVENT !!!
B16D9:00-89 - Unknown Error
B1395:00-08 - FIRING LOOPS INTERCONNECT
B1485:00-89 - PASSENGER AIRBAG RESISTANCE TOO HIGH (2ND STAGE)
B1620:00-89 - !!! SRSCM INTERNAL FAILURE !!!
B1116:00-08 - SENSOR GROUND
B2617:00-08 - Unknown Error
B1102:00-08 - BATTERY VOLTAGE LOW VOLTAGE. ( < 8V )
B1742:00-89 - P-SIS(SIDE IMPACT SENSOR PRESSURE) FRONT-DRIVER COMMUNICATION ERROR
B14AE:00-89 - Unknown Error
B1513:00-89 - PASSENGER BELT SWITCH-OPEN/SHORT TO BATTERY
diagnostics 07/23/2021

Read ECU Delivery Assembly Number...
95910-T6100
Read Errors... ok
B1473:00-89 - INFLATABLE CURTAIN AIRBAG DRIVER RESISTANCE TOO HIGH
B2502:00-89 - WARNING LAMP 2
B1477:00-89 - PASSENGER CURTAIN RESISTANCE.-HIGH
B1361:00-89 - PRETENSIONER FRONT-DRIVER RESISTANCE TOO HIGH
B1367:00-89 - PRETENSIONER FRONT-PASSENGER RESISTANCE TOO HIGH
B1711:00-89 - KNEE AIRBAG FRONT DRIVER RESISTANCE TOO HIGH
B1356:00-89 - REAR AIRBAG RESISTANCE TOO LOW
B1481:00-89 - DRIVER AIR BAG(DAB) RESISTANCE-HIGH(2ND)
B14AE:00-89 - Unknown Error
B1511:00-89 - DRIVER BELT SWITCH-OPEN/SHORT TO BATTERY



a lot of airbags not installed yet so there are still bugs but b1649 b1650 b1620 missing after repair.

[qsrkoly]

And if You have Smart-OBD please Check 95910-S2000 for Read and Write data via OBD (possible in car and table)..
Post Result!

Enable 12V on Extended Connector... ok
External power +13,67V
Set ServiceMode... ok
Set ServiceMode... ok
Set ServiceMode... ok
Enter security... ok
Set Bootloader Addr... ok
Load Bootloader... ok
Enter Bootloader... ok
Send Read Address... ok
Creating backup "Hyundai 95910-S2000 TC23xx-32F 23.07.2021 16.17.40.bin"... ok
Reading EEPROM... Can't Read EEPROM Page0

no read via obd connector

[smart-prog]

Ok i see after write clear dump error all Ok!
For added read write via OBD need this ecu in hand!