Tweet
Unfortunately, I don't have any.
-
-
Collision number 1 still exists
Crash Counters...
Frontal collision - 1
Driver side collision - 0
Passanger side collision - 0
Rear collision - 0
Rollover Detection - 0
Active Head Restraint (AHR) System Deployed - failed
Pedestrian Protection Deployed - 0
Crash Event Status - 0
Read Errors...
P100B:00-09 - Unknown Error
P1019:00-09 - Unknown Error
B1000:1B-89 - DRIVER AIRBAG IGNITER (Circuit Resistance Above Threshold)
B1002:1B-89 - IGNITER FOR PASSENGER SIDE AIRBAG (Circuit Resistance Above Threshold)
B1006:1B-89 - DRIVER SIDE SEAT BELT TENSION IGNITER (Circuit Resistance Above Threshold)
B1007:1B-89 - PASSENGER SIDE SEAT BELT TENSION IGNITER (Circuit Resistance Above Threshold)
B100A:1B-89 - FRONT PASSENGER SIDE AIRBAG IGNITER (Circuit Resistance Above Threshold)
B100B:1B-89 - DRIVER SIDE AIRBAG IGNITER (Circuit Resistance Above Threshold)
B1017:13-89 - DRIVER s SIDE AIRBAG CRASH SENSOR (Circuit Open)
B101A:13-89 - DRIVER s FRONT AIRBAG CRASH SENSOR (Circuit Open)
B1027:13-89 - PASSENGER SIDE SEAT OCCUPIED SENSOR (Circuit Open)
B1036:13-89 - CRASH SENSOR SIDE AIRBAG PASSENGER SIDE (Circuit Open)
B13BC:F2-89 - MUITIBLE COLLISION BRAKE (ABS CONNECTION) ()
U0002:00-09 - POWERTRAIN DATABUS NO COMMUNICATIONS
U2A62:00-89 - Unknown Error
--------------------------------------------------------
Opened file: C:\Users\lxgqi\Desktop\2024-4-28_11'19'56'_95256.bin
--------------------------------------------------------
Clearing Crash by Dump... ok
Saved file: C:\Users\lxgqi\Desktop\2024-4-28_11'19'56'_95256_cleared_by_AST.bin
--------------------------------------------------------
Enable 12V on Extended Connector... ok
External power +13.21V
Set ServiceMode... ok
Clear errors... ok
Comment
-
For clear crash counter use airbag service tool by dump! Support this part number!Comment
-
I have checked this SAS with other workshop programmers. all of them told me that Toyota Hilux SAS 0K020 can not reset with any device now....Today, 03:04 -
Reply to 95910-1w500. Can we change coding?You do not have permission to view this gallery.
This gallery has 3 photos.Today, 02:59 -
Hi there. I have to replace a module for a Kia rio. I old unit is no coms. New unit can connect. Clear crash. Clear codes. But units coding (read by ast)...Today, 02:57
-
Reply to Reset airbag module ml3t-14b321-yeFor MB3T ending in "YE", I always have to use direct solder method and then read/write with CPT....Yesterday, 22:05
-
Hello, I bought new Smart-Prog 2 months ago and today due to overvoltage fault from my power supply my Smart-Prog blew up some component inside, looks...Yesterday, 19:25
-
Reply to Reset airbag module ml3t-14b321-yeTry Clear Crash by OBD using model MB3T-14B321-BB.Yesterday, 18:09
-
BRAND: FORD
ID MODULE: ML3T-14B321-YE
Hi, how are you? Can you help me. I'm trying to reset this module but it tells me that the Clear...Yesterday, 17:40 -
Reply to 95910-A4350 ver1.2Tak zrobiŁem odczytaŁem po benchu zapisaŁem cpt i zostaŁ jeden bŁad b1620 i nie da siĘ kasowaĆ bŁedYesterday, 17:31
-
-
-
This SAS may be damaged or have incorrect data written to it.Yesterday, 16:38
-
Reply to 95910-A4350 ver1.2It was first diagnostic of the new SRS ECU on the bench? Or after installation on the car.
Read Errors...
B1650:00-89 - !!! CRASH RECORDED...Yesterday, 16:23 -
Reply to 95910-A4350 ver1.2Witam kupiŁem drugi sterownik niestety tez z wypadkiem i dostaŁem caŁy samochod odczyt po pinach wgrywanie na stole poskrecany wlozony...Yesterday, 15:00
-
Reply to 95910-A4350 ver1.2Witam kupiŁem drugi sterownik niestety teŻ z wypadkiem i dostaŁem caŁy samoch...Yesterday, 14:59
-
I did it sevral times without success...Yesterday, 14:40
Comment