2016 SUBARU CROSSTECK 98221FJ490 did not work on bench with smart obd

[Rookie2018]

hello guys i followed all steps and i know i have to remove 0resistor and add 10k to write module but when i put module on car everything is still on there but only as history. i try to erase everything with scanner but it doesn't go away. any suggestions . i also did it twice


Processing... 02.08.2022 17.11.45
Checking new version... ok
Connection to server... ok
Checking security... ok
External power +15.19V
Start Manual Mode for 98221FJ490 (by CAN)
Enable 12V on Extended Connector... ok
External power +15.15V
Set ServiceMode... ok
Read ECU Serial Number...
98221FJ490
Read Errors...
B1618:2E-00 - FRONT SUB SENSOR LH INITIALIZATION ERROR
B1677:2E-00 - SATELLITE SAFING SENSOR INITIALIZATION INCOMPLETE
B1801:2E-00 - OPEN IN DRIVER'S AIRBAG
B1811:2E-00 - OPEN IN DRIVER'S AIRBAG DUAL STAGE - 2ND STEP
B1806:2E-00 - OPEN IN PASSENGER'S AIRBAG
B1816:2E-00 - OPEN IN PASSENGER'S AIRBAG DUAL STAGE - 2ND STEP
B1901:2E-00 - OPEN IN FRONT P/T RH
B1906:2E-00 - OPEN IN FRONT P/T LH
B1861:2E-00 - OPEN IN DRIVER’S KNEE AIRBAG
B1821:2E-00 - OPEN IN SIDE AIRBAG RH
B1826:2E-00 - OPEN IN SIDE AIRBAG LH
B1831:2E-00 - OPEN IN CURTAIN AIRBAG RH SQUIB CIRCUIT
B1836:2E-00 - OPEN IN CURTAIN AIRBAG LH SQUIB CIRCUIT
B19F1:2E-00 - OPEN IN FRONT P/T 2 RH
B1623:2E-00 - SIDE AIRBAG SENSOR RH INITIALIZATION ERROR
B1628:2E-00 - SIDE AIRBAG SENSOR LH INITIALIZATION ERROR
B1660:2E-00 - PASSENGER’S AIRBAG ON INDICATOR FAILURE
B16F0:2E-00 - PASSENGER’S AIRBAG OFF INDICATOR FAILURE
B1650:2E-00 - OCCUPANT DETECTION SYSTEM MALFUNCTION
B11E0:28-00 - !!! ROLLOVER DEPLOYMENT HISTORY !!!
B1902:28-00 - SHORT IN FRONT P/T RH (TO GROUND)

Enable 12V on Extended Connector... ok
External power +15.15V
Set ServiceMode... ok
Read ECU Serial Number...
98221FJ490
Enter security... ok
Creating backup "Subaru 98221FJ490 H8SX1725 02.08.2022 17.13.07.bin" ok
Reading EEPROM... ok

Warning!!!
TURN OFF IGNITION OR 12V POWER SUPPLY FROM AIRBAG, WAIT 30 SECONDS AND TURN ON

Connection to server... ok
Dongle security device not found.
Please reconnect Dongle, and try again.
Connection to server... ok
Enable 12V on Extended Connector... ok
External power +15.12V
Set ServiceMode... ok
Enter security... ok
Erase Flash... ok

Enable 12V on Extended Connector... ok
External power +15.16V
Set ServiceMode... ok
Load Bootloader... ok
Enter Bootloader... ok
Erase EEPROM... ok
Set ServiceMode... ok
Prepare write... ok
Writing EEPROM... ok

Warning!!!
TURN OFF IGNITION OR 12V POWER SUPPLY FROM AIRBAG, WAIT 30 SECONDS AND TURN ON

Enable 12V on Extended Connector... ok
External power +15.14V
Clear errors... failed. It works only on car with all SRS security repaired!!!

[maximus_td]

It works only on car with all SRS security repaired!!!

restore all security and only then errors will be deleted

[Infinicartech]

Hi mate, your module is ok.
Install the module on car and repair all damage component, then clear errors. That's it

[Rookie2018]

I repaired all components, went from current to history.

they won’t go away after that.

[maximus_td]

Do the cleaning procedure again and after recording, turn off the power and do not feed it to the unit on the table, immediately install it in the car. I'm sure you will have one or more errors.
Check the rear belts, on subaru they also often trigger, but the belts are not blocked

[Rookie2018]

thanks for tip. I guess i will try it next time , client couldn’t wait…